07eins GmbH
PD injector bridge 1.2 TDI & 1.4 TDI set – 3 PD injector retainers
PD injector bridge 1.2 TDI & 1.4 TDI set – 3 PD injector retainers
Suitable for all Audi, Seat, Skoda, and VW TDI engines with PD technology (pump-nozzle units).
The PD injector retainers are the PD injector bridge for 1.2 TDI & 1.4 TDI 3-cylinder engines with unit injectors and prevent the PD injectors from moving as a result of the design.
SKU:071MTR001PDEK-03
In stock
Permanently leak-proof and ⅔ cheaper than a cylinder head replacement!
Availability for pickups could not be loaded
ORIGINAL PD injector retainer set of 3
The PD injector bridge for 1.2 TDI and 1.4 TDI 3-cylinder engines with unit injectors
If your 1.2 TDI or 1.4 TDI is harder to start, runs roughly, judders or the oil level rises, there is often more behind it than just a minor leak. The ORIGINAL 07eins PD injector retainer set of 3 acts where the underlying problem arises — directly at the unit injector seat.
Proven 07eins solution for TDI engines with unit injectors.
Even after installation, if there is no improvement.
Developed for typical 3-cylinder unit injector engines with Bosch injectors.
The original 07eins solution for 1.2 TDI and 1.4 TDI 3-cylinder PD-TDI engines.
Many 3-cylinder TDI problems seem minor — until they become expensive.
A rough idle. Poorer starting. Juddering. Less power. A rising oil level. At first, this seems like a normal sign of ageing. In fact, the cause may lie deeper: at the unit injector itself.
The ORIGINAL 07eins PD injector retainer set of 3 stabilises the PD injectors precisely where movement, leaks and consequential damage can arise — directly in the cylinder head.
Symptoms you may notice too
Many drivers initially search not for PD injector retainers but for the symptoms: poor starting, juddering, loss of power or a rising oil level. These are precisely the signs that can occur in TDI engines with unit injectors when the unit injectors are no longer seated properly in the cylinder head, move slightly or their seals no longer seal reliably.
The engine is harder to start than before — especially when cold, warm or after a long period of standing. It often needs prolonged cranking before the TDI runs properly.
The vehicle runs more roughly or unevenly at a standstill, or seems to shake more. This may indicate an incorrect PD injector position, leakage or uneven injection.
While driving, the engine responds less smoothly, pulls less strongly or no longer runs as confidently as before. Altered injection conditions can noticeably affect engine performance.
The oil level appears to rise or the engine oil smells of diesel. The cause may be diesel in the engine oil — a risk to the bearings, camshaft, turbocharger and engine lubrication in general.
The seals have already been replaced, yet the symptoms return. In that case, the cause often lies not just in the seal itself but in the mechanical seating of the PD injector.
If PD injectors continue to wear into the cylinder head, the sealing surfaces can suffer further damage. That is precisely why mechanical stabilisation is particularly important.
What the PD injector retainer set of 3 specifically improves
The ORIGINAL 07eins PD injector retainers surround and stabilise the three unit injectors where the problems arise. Less movement means less risk of recurring leaks, renewed tilting and further stress at the seats in the cylinder head.
Suitable for 1.2 TDI and 1.4 TDI engine codes
The set of 3 is designed for 1.2 TDI and 1.4 TDI 3-cylinder engines with unit injectors. Here is the complete engine code (MKB) overview:
Important: The specific engine and PD injector version are always decisive. If your engine code is not listed or you are unsure, you should check compatibility beforehand.
Typical vehicles with 1.2 TDI / 1.4 TDI 3-cylinder PD injector engines
Important: The specific engine and PD injector version are always decisive. If in doubt, you should check compatibility beforehand.
The key benefits — clear and concise
The original: developed by 07eins
The original PD injector retainers were developed by 07eins in 2020 and have since become the proven solution for many TDI engines with a unit injector system. For 1.2 TDI and 1.4 TDI 3-cylinder engines, they are the PD injector bridge and a proven way to repair damaged cylinder heads and prevent damage to injector sealing seats that threatens their function.
The system allows straightforward installation and removal. The PD injector retainers secure the PD injectors so that they return to their original position and can no longer wear further into the cylinder head due to engine vibrations.
In many cases, early use can help prevent consequential damage and improve sealing over the long term. However, effectiveness always depends on the condition and existing damage to the seating surfaces.
Scope of delivery for the set of 3
- 3x ORIGINAL 07eins PD injector retainers
- 6x countersunk screws M4 x 10 mm
- 3x support shims 1.0 mm
- 3x support shims 0.5 mm
- 3x support shims 0.25 mm
Our recommendation before cylinder head replacement
Try PD injector retainers first.
Particularly in older vehicles with high mileages, several sources of faults may be present at the same time. That is why 07eins offers an extended right of return for the use of PD injector retainers.
If there is no improvement in your vehicle, you can return the product within 6 months for a refund of the purchase price — regardless of whether there are signs of use.
Installation costs, removal costs, consumables, diagnostic costs and other consequential costs are excluded.
Additional support on the 07eins website
Delivery time
Available for immediate delivery once payment has been received. Orders received and paid for by 11:00 are generally dispatched the same day.
Prefer professional installation? Over 500 partner workshops across Europe
Not everyone wants to carry out the installation themselves. That is why 07eins works with over 500 partner workshops across Europe that can professionally install the ORIGINAL 07eins PD injector retainers.
Important note on effectiveness
All engine or unit injector solutions from 07eins are designed to minimise the effects of the original factory design flaws in the engines concerned or reduce their symptoms.
Early use of the products can positively influence the life of the cylinder head and limit the effects of damage that has already occurred. However, even our products cannot compensate for excessively advanced wear marks and damage to the sealing surfaces.
Any installation costs, removal costs, consumables, diagnostic costs and other consequential costs are always borne by the customer and will not be reimbursed.
Do not wait for minor symptoms to become major damage.
The ORIGINAL 07eins PD injector retainer set of 3 is the proven solution for 1.2 TDI and 1.4 TDI 3-cylinder unit injector engines when starting problems, loss of power, leaks or a rising oil level should not keep returning.
1.2 & 1.4 TDI engine code letters (affected engines)
1.2 & 1.4 TDI engine code letters (affected engines)
AMF, ANM, ANY, APE, ASY, ATL, AYZ, BAY, BHC, BMS, BNM, BNV, BWB
If your engine code letter (MKB) is not listed, it is still possible that the engine is affected!
Contact us us quickly and we will check your MKB to make sure!
If your engine is affected, we will add it to the list immediately!
This will help other affected TDI drivers. Thank you very much! 🙏🏻
Our recommendation for severely damaged cylinder heads
Our recommendation for severely damaged cylinder heads
Reinforced VITON gasket rings in combination with our original PDE bridge also help in the event of severe run-in marks in the cylinder head: thanks to their larger diameter than the standard gasket rings, they keep the cylinder head tight again, while the PDE bridge fixes the PDEs in place and prevents them from working their way back into the cylinder head.
6-month right of return
6-month right of return
See for yourself - without any risk!
If the product does not meet your expectations, you can easily within 6 months You only have to pay the shipping costs.
Before replacing the cylinder head - test the PDE bridge!
Unfortunately, in older vehicles with high mileages, the sources of faults are always varied.
We would like to support you in your decision to repair and therefore offer you the following for the use of our products Extended right of return.
If there is no improvement to your vehicle, you can use our products 6 months The product can be returned for a full refund of the purchase price, regardless of whether there are any signs of use (assembly/disassembly costs, consumables and follow-up costs are excluded).
Legal guarantee
Legal guarantee
Fast delivery times (DHL, DHL Express, UPS)
Fast delivery times (DHL, DHL Express, UPS)
We ship orders that received and paid by 11:00 are, same day (Mondays to Fridays) by DHL.
Express deliveries are made by UPS or DHL Express delivered.
Scope of delivery
Scope of delivery
Each set contains carcase holders, end support dimensions and 07eins PDA screws for PDE body holder M4 x 10
Set of 1 contains:
- 1 x PDE body holder
- 2 x countersunk head screw for PDE body holder Thread size M4 x 10 mm
- 1 x 1 mm, 1 x 0.5 mm and 1 x 0.25 mm End support dimensions
Set of 2 contains:
- 2 x PDE body holder
- 4 x countersunk head screw for PDE body holder Thread size M4 x 10 mm
- 2 x 1 mm, 2 x 0.5 mm and 2 x 0.25 mm End support dimensions
Set of 3 contains:
- 3 x PDE body holder
- 6 x countersunk head screw for PDE body holder Thread size M4 x 10 mm
- 3 x 1 mm, 3 x 0.5 mm and 3 x 0.25 mm End support dimensions
Set of 4 contains:
- 4 x PDE body holders
- 8 x countersunk head screw for PDE body holder Thread size M4 x 10 mm
- 4 x 1 mm, 4 x 0.5 mm and 4 x 0.25 mm End support dimensions
Set of 5 contains:
- 5 x PDE body holder
- 10 x countersunk head screw for PDE body holder Thread size M4 x 10 mm
- 5 x 1 mm, 5 x 0.5 mm and 5 x 0.25 mm End support dimensions
Set of 10 contains:
- 10 x PDE body holder
- 20 x countersunk head screw for PDE body holder Thread size M4 x 10 mm
- 10 x 1 mm, 10 x 0.5 mm and 10 x 0.25 mm End support dimensions
End support dimensions for 07eins PDE body holder / PDE repair holder in thicknesses of 1 mm, 0.5 mm and 0.25 mm. 1 end support dimension is required per PDE.
Manufacturer
Manufacturer
07eins GmbH
Willenbach 12
84367 Reut
Germany
Email: info@07eins.com
Notes
Notes
All products from 07eins / engine (pump-nozzle remedy) are designed to minimize the effects of existing factory design defects on the engines concerned or to reduce their symptoms. Early use of the products can have a positive influence on the service life of the cylinder head and limit the effects of damage that has already occurred. However, our products are not able to compensate for excessive running-in marks and damage to the sealing surfaces. Any assembly/disassembly costs incurred as a result of use, consumables and follow-up costs are always the responsibility of the customer and will not be reimbursed by Pumpe-Düse-Abhilfe.
DÜSENFUCHS - your contact when it comes to injectors!
- DÜSENFUCHS is the official sales and cooperation partner of the 07eins GmbH
- DÜSENFUCHS Overhauled pump-nozzle elements from 07eins recommended!
Share
Questions about this product
What are PDE body supports – and are PDE repair supports the same thing?
PDE body supports provide additional stabilisation for the body of each unit injector in the cylinder head. This reduces movement and relieves stress on the seal at the PDE seat. They are also referred to as PDE repair supports on the market. The individual supports also allow suitable solutions for engine designs where there is no room for the classic PDE bridge.
For which engines are PD injector retainers available?
PD injector retainers are available in versions suitable for VAG unit injector engines with 3, 4, 5 or 10 cylinders. The selection depends on the engine and the specific PD injector variant actually fitted. Please provide the vehicle details and engine code letters for identification; a model designation or the lettering ‘TDI’ alone is not sufficient for this purpose.
How do you fit PD injector retainers?
The PD injector retainers are fitted to the individual unit injectors in accordance with the relevant fitting instructions. During this process, the PD injectors and seating surfaces are checked, and the specified seals and screws are replaced. Access and the steps involved vary depending on the engine; therefore, select the instructions for your specific application.
What is the experience with PD injector retainers?
07eins’ PD injector retainers have already been successfully fitted in VAG TDI engines more than 5,000 times. Customers and garages have reported positively on this repair solution; garages confirm its effectiveness in resolving the PD injector issues described.
Does the cylinder head need to be machined to fit the PD injector bridge or PD injector retainer?
The 07eins PDE injector bridge and PDE injector retainer are designed as retrofit solutions that do not require conventional machining of the PDE seats. This avoids time-consuming seat machining. A prerequisite is that the condition of the cylinder head and engine still allows for this repair method.
Die PD-Injektorhalter von 07eins sind eine einzigartige Lösung. Eine interessante technische Zusatzlösung zur Injektormontage zur Verlängerung der Funktionalität und Lebensdauer des Motors, die das Ingenieurteam der VAG-Gruppe nicht realisieren konnte. Präzise Verarbeitung, schnelle Lieferung ab Bestellung. Nach der Selbstmontage der Halter, dem Einbau der Injektoren und der Einstellung der Injektoren gemäß den ŠKODA-Werkseinstellungen verringert sich das Motorgeräusch. Ich empfehle es allen, die ihren PD-Motor retten und verewigen möchten.
De momento va bien, espero que dure
Hat perfekt gepasst.
Reviews in Other Languages
Buone istruzione esaustive consegna in tempi brevi troppo care
Bonjour.Produit de qualité ,correspond à la description.Bonne transaction.Livraison rapide.
Minden rendben van, köszönöm.