VW T5 Transporter / Panel Van / Estate
2.5 TDI · 96 kW / 130 PS
AXD BNZ
Access Denied
IMPORTANT! If you’re a store owner, please make sure you have Customer accounts enabled in your Store Admin, as you have customer based locks set up with EasyLockdown app. Enable Customer Accounts
1
/
from
14
07eins GmbH
ORIGINAL PDE Bridge for VW Touareg 7L 2.5 TDI | BAC BLK BPE BPD
ORIGINAL PDE Bridge for VW Touareg 7L 2.5 TDI | BAC BLK BPE BPD
Suitable for all Audi, Seat, Skoda, and VW TDI engines with PD technology (pump-nozzle units).
Prevent cylinder head damage in the VW Touareg 7L 2.5 TDI. The ORIGINAL 07eins PD injector bridge permanently stabilizes unit injector injectors in the R5 engine.
4.69 von 5 | 78 Bewertungen
SKU:071MTR002PDEB-AT
In stock
Permanently leak-proof and ⅔ cheaper than a cylinder head replacement!
Normal price
399,00 €
Normal price
449,00 €
Selling price
399,00 €
Base price
/
per
Incl. taxes (EU) / excl. taxes (outside EU and outside DE with VAT-ID).
Shipping will be charged at checkout
Quantity
Availability for pickups could not be loaded
Original from 07eins
ORIGINAL PD injector bridge for VW Touareg 7L 2.5 TDI – Engine code letters BAC BLK BPE BPD
Repair kit for the permanent centring of the unit injectors
The tried-and-tested ‘ 07eins ’ solution for VW T5 2.5 TDI pump-jet TDI engines with unit injectors: designed to permanently secure and centre the unit injectors in the aluminium cylinder head — without the need for any machining of the cylinder head.
Maximum holding force for the Touareg 2.5 TDI – protection against worn injector seats under high engine load.
In the VW Touareg 7L, the 2.5 TDI R5 engine has to cope with heavy vehicle weights and is often used to tow trailers or for off-road driving. The high torque and thermal cycling exacerbate the typical movement of the unit injectors within the cylinder head. The consequences in the Touareg: starting problems after short periods of inactivity, jerking under load and gradual oil dilution caused by diesel fuel entering the system.
With the ORIGINAL 07eins® PD injector bridge You can prevent the impending financial disaster caused by having to replace the cylinder head. It centres the injectors in their seats and restores the correct seal.
Multi-piece PD injector bridge with aluminium connecting strip and tool steel brackets Original ‘ 07eins ’ quality since 2015
10,000+
TDIs fitted worldwide
Tried-and-tested solution for VW T5 2.5 TDI pump-jet TDI engines with unit injectors.
6 months
money-back guarantee
Even after fitting, if no improvement is seen.
500+
partner garages
Qualified garages for installation near you.
2015
Developed by 07eins
The original PD injector bridge from the inventor of the solution.
When the PDEs start to shift, that’s when the real problem begins.
In 2.5 TDI pump-jet TDI engines with unit injectors from the VW Group, the unit injectors can become displaced within the cylinder head or wear into the sealing surfaces due to vibrations and stress. The result: the sealing rings no longer sit correctly, the seal deteriorates and typical PDE problems can arise.
The ORIGINAL 07eins PD injector bridge permanently secures and centres the unit injectors in the cylinder head. The sealing rings remain in their correct position and can seal reliably.
Identifying typical PDE problems
These symptoms may indicate wandering or leaking PDEs
Many TDI drivers do not initially look for a PD injector bridge, but rather for the symptoms: poor starting, jerking, loss of power, diesel in the oil or a rising oil level. It is precisely these signs that can occur in the VW T5 2.5 TDI if the unit injectors in the cylinder head no longer fit properly, move slightly or the seals no longer provide a reliable seal.
Starting difficulties when cold or warm
The engine starts less easily in the morning, after a long period of inactivity, or even when warm. Often, you have to crank it for longer before the TDI runs smoothly.
Uneven engine running and jerking
The engine runs roughly at idle, shakes or responds unevenly whilst driving. This may indicate a misaligned PD injector, a leak or uneven fuel injection.
Loss of power and reduced torque
The TDI no longer pulls as it used to, accelerates more sluggishly or feels less powerful under load. An imperfect seal or altered injection conditions can noticeably impair engine performance.
Oil dilution / rising oil level
The oil level appears to be rising, or the engine oil smells of diesel. This may be caused by diesel in the engine oil — a risk to bearings, the camshaft, the turbocharger and general engine lubrication.
Smell of diesel or fuel ingress
If diesel fuel leaks past the unit injector seals, this may be noticeable through a smell of fuel, changes in the oil or unusual starting behaviour.
Increased fuel consumption
If the engine is no longer injecting fuel properly or is no longer burning fuel efficiently, diesel consumption may increase. This symptom is often first noticed during everyday driving or on longer journeys.
Smoke coming from the exhaust
Black or bluish smoke may indicate incomplete combustion, oil burning or a faulty injection system. This should be checked, particularly if accompanied by starting problems or jerking.
Recurring leaks despite new seals
If unit injector seals have already been replaced and the problems recur, the cause often lies deeper: the PD injectors must be mechanically stabilised so that the seal can operate permanently in its intended position.
What the PD injector bridge does
Permanently centres the PDEs The unit injectors are securely guided within the cylinder head and prevented from shifting further.
Improves the seal The sealing rings remain in their intended position and can seal correctly once again.
Can help avoid the need for a cylinder head replacement In many cases, re-centred PDEs can re-seal even where the sealing surfaces are already damaged. The effectiveness depends on the condition of the sealing surfaces.
Fits without machining the cylinder head Fitting requires no modifications to the cylinder head or associated components.
Multi-piece rather than a rigid single-piece design
Why the 07eins PD injector bridge is deliberately designed differently
A PD injector bridge must do more than simply connect the unit injectors as rigidly as possible. What matters is how the system behaves under real-world engine conditions: during cold starts, when warming up, under vibration, during load changes and during subsequent cooling.
This is precisely why 07eins relies on a multi-part PD injector bridge with an aluminium connecting strip and tool steel brackets. The bridge’s elongated structure operates thermally closer to the aluminium cylinder head. The highly stressed clamping areas are made of tool steel — precisely where the holding force is really needed.
The technical core: aluminium behaves differently to steel
The cylinder head of the VW T5 2.5 TDI is made of aluminium. Aluminium expands significantly more than steel when heated. During operation, the cylinder head can move along the length of the PD injector bridge by an amount that is technically significant in engine construction.
Aluminium for long-term durability
The connecting strip better matches the thermal behaviour of the aluminium cylinder head.
Tool steel for clamping forces
The U-brackets secure the PDEs precisely where high local forces are exerted.
Low-stress design for the cylinder head
The design is intended to stabilise the engine without introducing unnecessary additional stresses.
In short: 07eins uses tool steel not less, but more selectively. The aim is not maximum rigidity, but a technically sound fixation under real engine conditions.
Design comparison
07eins ’s multi-piece PD injector bridge vs. rigid, one-piece tool steel PD injector bridge
It is not maximum rigidity that determines an effective PD injector mounting, but rather the interplay of holding force, tolerance compensation, thermal behaviour and low-stress installation in the aluminium cylinder head of the VW T5 2.5 TDI.
✓
07eins PD injector bridge
Multi-part construction comprising an aluminium connecting strip and tool steel brackets.
✓ Material compatible with the cylinder head Aluminium where the bridge spans the length of the aluminium cylinder head.
✓ Tool steel at the load-bearing points The clamping brackets are made of tool steel — precisely where high local holding forces are required.
✓ Improved tolerance compensation The modular system supports a more even distribution of pressure between the individual PDEs.
✓ Low-stress mounting Designed to stabilise PDEs without introducing unnecessary additional stresses into the aluminium cylinder head.
✓ Easy to service Multi-part design with individual components for easier assembly, disassembly and subsequent servicing.
–
Rigid, one-piece tool steel PD injector bridge
Fully rigid construction made from tool steel.
– Steel along the entire length Tool steel is very strong, but does not follow the thermal behaviour of the aluminium cylinder head to the same extent.
– Maximum rigidity as a guiding principle A very rigid bridge is less able to accommodate component tolerances and thermal movement.
– Less structural flexibility Due to its design, a one-piece system offers less compensation between individual injectors.
– Potentially higher voltage induction A long, rigid steel structure can contribute to additional mechanical stresses in the cylinder head during temperature fluctuations.
– Less flexible in terms of servicing A one-piece assembly may be less service-friendly when it comes to handling and subsequent work.
Conclusion: controlled flexibility rather than maximum rigidity.
07eins ’s PD injector bridge combines an aluminium connecting strip with precision tool steel brackets. This ensures that the clamping force is applied exactly where it is needed, whilst the long bridge structure is better suited to the thermal behaviour of the aluminium cylinder head. The aim: to stabilise PDEs permanently, secure them more evenly and relieve the cylinder head of stress as much as possible.
Note: This comparison outlines the design differences between the multi-piece 07eins PD injector bridge with aluminium connecting strip and tool steel brackets and a rigid, single-piece tool steel PD injector bridge. Set components such as seals, the wiring harness, the PFS kit or the fitting kit are deliberately not included in this comparison.
Compatibility by model, engine type and MKB
Suitable for 2.5 TDI / R5 TDI pump-jet TDI engines with unit injectors from the VW Group
The ORIGINAL 07eins PD injector bridge is designed for relevant 2.5 TDI pump-jet TDI engines with unit injectors from the VW Group. The vehicle model, engine variant and engine code letter are crucial for identification.
Important: Always check your vehicle’s engine code before ordering. Codes that look particularly similar, such as BLJ and BJL must not be confused.
Main application
VW T5 2.5 TDI
Transporter, Panel Van, Estate, Multivan, Bus, Caravelle, California and 4motion.
VW T5 Transporter / Panel Van / Estate
2.5 TDI · 128 kW / 174 PS
AXE BPC
VW T5 Multivan
2.5 TDI · 96 kW / 130 PS
AXD BNZ
VW T5 Multivan
2.5 TDI · 128 kW / 174 PS
AXE BPC
VW T5 Multivan / van
2.5 TDI · 120 kW / 163 PS
BLJ
VW T5 Caravelle
2.5 TDI · 96 kW / 130 PS
AXD BNZ
VW T5 Caravelle
2.5 TDI · 128 kW / 174 PS
AXE BPC
VW T5 California
2.5 TDI · 96 kW / 130 PS
AXD BNZ
VW T5 California
2.5 TDI · 128 kW / 174 PS
AXE BPC
VW T5 4Motion
2.5 TDI · 96 kW / 130 PS
AXD BNZ
VW T5 4Motion
2.5 TDI · 128 kW / 174 PS
AXE BPC
Further 2.5 R5 TDI compatibility
VW Touareg 7L
2.5 R5 TDI pump-jet TDI engines with a different installation configuration to the VW T5.
VW Touareg 7L
2.5 R5 TDI · 128 kW / 174 PS
BAC BPE
VW Touareg 7L
2.5 R5 TDI · 120 kW / 163 PS
BLK BPD
Additional MKB test recommended
More VW Commercial Vehicles
These codes originate from the wider 2.5 TDI range and should be checked against your specific vehicle before ordering.
VW LT 28–46 / LT35
2.5 TDI · approx. 61–70 kW
BBE BBF
VW Crafter 30–50
2.5 TDI · 100 kW / 136 PS
BJL
All MKBs mentioned
AXD AXE BAC BBE BBF BJL BLJ BLK BNZ BPC BPD BPE
The original: developed by 07eins
The original PD injector bridge was developed by 07eins back in 2015 and has since been fitted in over 10,000 vehicles worldwide. It is a tried-and-tested solution for repairing damaged cylinder heads and for preventing damage to the injector seal seats that could compromise functionality.
The modular, utility model-protected system allows for hassle-free assembly and disassembly. The flexible connecting strip made from a special aluminium alloy accommodates the necessary tolerance variations between the individual injectors and ensures even pressure distribution.
In many cases, the newly centred PDEs can re-seal even where the sealing surfaces are already damaged. However, their effectiveness depends on the condition of the seating surfaces and any pre-existing damage.
Our recommendation before replacing the cylinder head
Test the PD injector bridge first.
Particularly in older vehicles with high mileage, several sources of faults may be present simultaneously. That is why 07eins offers an extended returns policy for the use of the PD injector bridge.
6-month return guarantee
If you do not notice any improvement in your vehicle’s performance, you can return the product within 6 months for a refund of the purchase price — regardless of whether there are signs of use.
Installation costs, removal costs, consumables, diagnostic costs and other associated costs are excluded from this.
Additional support on the 07eins website
Step-by-step installation guide Described in detail and structured with practical application in mind. Installation instructions
Workshop finder with over 500 partner workshops Have the PD injector bridge fitted by a qualified professional workshop near you. Find a workshop
customer reviews Numerous real-world reviews will help you make your decision. Read user reviews
Contents of delivery
- 1x ORIGINAL 07eins PD injector bridge
- 1x flexible connecting strip made from a special aluminium alloy
- 5x steel clamping brackets / tool steel brackets
- Mounting bolts
- Fixing clamps for the electrical connector strip
Delivery time
Available for immediate dispatch upon receipt of payment. Orders received and paid for by 11:00 am are usually dispatched the same day.
Important note on effectiveness
All products from 07eins / Engine or unit injector Remedies are designed to minimise the effects of factory-induced design flaws in the relevant engines or to alleviate their symptoms.
Using these products at an early stage can have a positive effect on the service life of the cylinder head and limit the impact of damage that has already occurred. However, even our products cannot compensate for wear marks and damage to the sealing surfaces that are too far advanced.
Any installation costs, dismantling costs, consumables, diagnostic costs and other associated costs are always borne by the customer and will not be reimbursed.
Buy the original PD injector bridge — direct from the inventor.
The tried-and-tested 07eins solution for VW T5 2.5 TDI common-rail engines with unit injectors: multi-piece PD injector bridge with aluminium connecting strip and tool steel brackets — designed for permanent centring, improved sealing and a low-stress fit within the aluminium cylinder head.
2.5 TDI engine code letters (affected engines)
2.5 TDI engine code letters (affected engines)
AXD, AXE, BAC, BBE, BBF, BJL, BLJ, BLK, BNZ, BPC, BPD, BPE
If your engine code letter (MKB) is not listed, it is still possible that the engine is affected!
Contact us us quickly and we will check your MKB to make sure!
If your engine is affected, we will add it to the list immediately!
This will help other affected TDI drivers. Thank you very much! 🙏🏻
Our recommendation for severely damaged cylinder heads
Our recommendation for severely damaged cylinder heads
Reinforced VITON gasket rings in combination with our original PDE bridge also help in the event of severe run-in marks in the cylinder head: thanks to their larger diameter than the standard gasket rings, they keep the cylinder head tight again, while the PDE bridge fixes the PDEs in place and prevents them from working their way back into the cylinder head.
6-month right of return
6-month right of return
See for yourself - without any risk!
If the product does not meet your expectations, you can easily within 6 months You only have to pay the shipping costs.
Before replacing the cylinder head - test the PDE bridge!
Unfortunately, in older vehicles with high mileages, the sources of faults are always varied.
We would like to support you in your decision to repair and therefore offer you the following for the use of our products Extended right of return.
If there is no improvement to your vehicle, you can use our products 6 months The product can be returned for a full refund of the purchase price, regardless of whether there are any signs of use (assembly/disassembly costs, consumables and follow-up costs are excluded).
Fast delivery times (DHL, DHL Express, UPS)
Fast delivery times (DHL, DHL Express, UPS)
We ship orders that received and paid by 11:00 are, same day (Mondays to Fridays) by DHL.
Express deliveries are made by UPS or DHL Express delivered.
Scope of delivery
Scope of delivery
- 1 x Flex connecting strip
- 5 x steel clamping brackets
- Mounting screws and
- Fixing clamps for the electrical connection strip
Manufacturer
Manufacturer
07eins GmbH
Willenbach 12
84367 Reut
Germany
Email: info@07eins.com
Notes
Notes
All products from 07eins / engine (pump-nozzle remedy) are designed to minimize the effects of existing factory design defects on the engines concerned or to reduce their symptoms. Early use of the products can have a positive influence on the service life of the cylinder head and limit the effects of damage that has already occurred. However, our products are not able to compensate for excessive running-in marks and damage to the sealing surfaces. Any assembly/disassembly costs incurred as a result of use, consumables and follow-up costs are always the responsibility of the customer and will not be reimbursed by Pumpe-Düse-Abhilfe.
DÜSENFUCHS - your contact when it comes to injectors!
- DÜSENFUCHS is the official sales and cooperation partner of the 07eins GmbH
- DÜSENFUCHS Overhauled pump-nozzle elements from 07eins recommended!
Share
L
Linus Genial entwickeltes Produkt um einem gravierenden Produktionsfehler entgegenzuwirken! Motor springt jedes einzelne Mal sofort und zuverlässig an.
S
Stephan Passt perfekt und die Anleitung ist auch sehr gut! Damit läuft der dicke wieder ein paar tausend kilometer
D
Dieter Die Brücke hat mir viel Arbeit und Kosten gespart. Mit 400.000 km schnurrt mein Motor wieder wie neu.
Reviews in Other Languages
A
Age Fluitman Mooi product, bedrijf is goed bereikbaar en reageert snel op mails en denkt mee in oplossingen.
5 sterren dik verdiend
I
Imrich Straka Perfektné. Krásne drží vstrekovače rovno na sedlo v hlave .
S
Sylvain Au top ! Un ensemble mécanique très bien pensé et parfaitement ajusté, l'installation est simple et le maintien des injecteurs semble efficace. L'expédition est très rapide, le service après vente est disponible et réactif, merci a Patricia :)
Invalid password
Enter